Class 12 Physics Electromagnetic Waves and Communication – Get here the Notes for Class 12 Physics Electromagnetic Waves and Communication. Candidates who are ambitious to qualify the Class 12 with good score can check this article for Notes. This is possible only when you have the best CBSE Class 12 Physics study material and a smart preparation plan. To assist you with that, we are here with notes. Hope these notes will helps you understand the important topics and remember the key points for exam point of view. Below we provided the Notes of Class 12 Physics for topic Electromagnetic Waves and Communication.
- Class: 12th
- Subject: Physics
- Topic: Electromagnetic Waves and Communication
- Resource: Notes
CBSE Notes Class 12 Physics Electromagnetic Waves and Communication
Candidates who are pursuing in Class 12 are advised to revise the notes from this post. With the help of Notes, candidates can plan their Strategy for particular weaker section of the subject and study hard. So, go ahead and check the Important Notes for Class 12 Physics Electromagnetic Waves and Communication.
It is a current which produces in the region in which the electric field and hence the electric flux changes with time.
Displacement current, ID = εo . dφE / dt
where, φE is the electric flux.
where, μo = Permeability
= 4π * 10-7 V / Am
This equation is Ampere-Maxwell law.
Electromagnetic waves are those waves in which electric and magnetic field vectors changes sinusoidally and are perpendicular to each other as well as at right angles to the direction of propagation of wave.
The equation of plane progressive electromagnetic wave can be written as E = Eo sin Ω (t – x / c) and B = Bo sin Ω (t – x / c). Where, Ω =2πv
Electromagnetic waves are produced by accelerated charge particles.
Properties of EM Waves
(i) These waves are transverse in nature.
(ii) These waves propagate through space with speed of light, i.e., 3 * 108 m / s.
(iii) The speed of electromagnetic wave,
c = 1 / √μo εo
where, μoo is permittivity of free space,
∴ c = Eo / Bo
where Eo and Bo are maximum values of electric and magnetic field vectors.
[According to Maxwell, when a charged particle is accelerated, it produces electromagnetic wave. The total radiant flux at any instant is given by,
p = q2a2 / 6 πεoc2
(iv) The rate of flow of energy in an electromagnetic wave is described by the vector S called the poynting vector, which is ; defined by the expression,
S = 1 / μo E * B
SI unit of Sis watt/m2.
(v) Its magnitude S is related to the rate at which energy is transported by a wave across a unit area at any instant.
(vi) The energy in electromagnetic waves is divided equally between electric field and magnetic field vectors.
(vii) The average electric energy density.
UE = 1 / 2 εo E2 = 1 / 4 εo E2o
(viii) The average magnetic energy density,
UB = 1 / 2 B2 / μo = 1 / B2o / μo
(ix) The electric vector is responsible for the optical effects of an electromagnetic wave.
(x) Intensity of electromagnetic wave is defined as energy crossing per unit area per unit time perpendicular to the directions of propagation of electromagnetic wave.
(xi) The intensity I is given by the relation,
I = < μ > c = 1 / 2 εo E2oc
(xii) The existence of electromagnetic waves was confirmed by Hertz experimentally in 1888.
Propagation of Electromagnetic Waves
In radio wave communication between two places. the electromagnetic waves are radiated out by the transmitter antenna at one place which travel through the space and reach the receiving antenna at the other place.
The arranged array of electromagnetic radiations in the sequence of their wavelength or frequency is called electromagnetic spectrum
Radio and microwaves are used in radio and TV communication,
Infrared rays are used to
(i) Treat muscular straw.
(ii) For taking photographs’ in fog or smoke.
(iii) In green house to keep plants warm.
(iv) In weather forecasting through infrared photography.
Ultraviolet rays are used
(i) In the study of molecular structure.
(ii) In sterilizing the surgical instruments.
(iii) In the detection of forged documents, £ringer prints.
X-rays are used
(i) In detecting faults, cracks, flaws and holes in metal products.
(ii) In the study of crystal structure.
(iii) For the detection of pearls in oysters.
γ – rays are used for the study of nuclear structure.
The gaseous envelope surrounding the earth is called earth’s atmosphere. It contain the following layers
(i) Troposphere This region extends upto a height of 12 km from earth’s surface.
(ii) Stratosphere This region extends from 12 km to 50 km. In this region, most of the atmospheric ozone is concentrated from 30 to 50 km. This layer is called ozone layer.
(iii) Mesosphere The region extends from 50 km to 80 km.
(iv) Ionosphere This region extends from 80 km to 400 km.
In ionosphere the electron density is very large in a region beyond 110 km from earth’s surface which extends vertically for a few kilometer.
This layer is called Kennelly Heaviside layer.
In ionosphere a layer having large electron density is found at height 250 km from earth’s surface, called Appleton layer.
There are four main layers in earth’s atmosphere having high density of electrons and positive ions, produced due to ionisation by the high energy particles coming from sun. star or cosmos. These layers play their effective role in space communication. These layers are D, E, F1 and F2.
(i) D-layer is at a virtual height of 65 km from surface of earth and having electron density = 109 m-3
(ii) E-layer is at a virtual height of 100 km, from the surface of earth, having electron density = 2 * 1011 m-3
(iii) F1-layer is at a virtual height of 180 km from the surface of earth, having electron density = 3 * 1011 m-3
(iv) F2 – layer is at a vertical height of about 300 km in night time and about 250 to 400 km in day time. The electron density of this layer is = 8 * 1011 m-3
Faithful transmission of information from one place to another place is called communication.
Optical fibers are used in optical communication.
A communication system contains three main parts
(i) Transmitter It process and encode the information and make it suitable for transmission.
The message signal for communication can be analog signals or digital signals.
An analog signal can be converted suitably into a digital signal and vice-versa.
[An analog signal is that in which current or voltage value varies continuously with time.
A digital signal is a discontinuous function of time. Such a signal is usually in the form of pulses.]
(ii) Communication Channel The medium through which information propagate from transmitter to receiver 1S called communication channel.
(iii) Receiver It receives and decode the signal.
A signal in which current or voltage changes its magnitude continuously with time, is called an analog signal.
A signal in which current or voltage have only two values, is called a digital signal.
Note An analog signal can be converted suitable Into a digital signal and vice-versa.
The process of superimposing the audio signal over a high frequency carrier wave is called modulation.
In the process of modulation anyone characteristic of carrier wave is varied in accordance with the instantaneous value of audio signal (modulating signal).
Need of Modulation
(i) Energy carried by low frequency audio waves (20 Hz to 20000 Hz) is very small.
(ii) For efficient radiation and reception of signal. the transmitting and receiving antennas should be very high approximately 5000 m.
(iii) The frequency range of audio signal is so small that overlapping of signals create a confusion.
Types of Modulation
(i) Amplitude Modulation In this type of modulation, the amplitude of high frequency carrier wave is varied in accordance to instantaneous amplitude of modulating signal.
Band width required for amplitude modulation
= twice the frequency of the modulating signal.
(ii) Frequency Modulation In this type of modulation, the frequency of high frequency carrier wave is varied in accordance to instantaneous frequency of modulating signal.
(iii) Pulse Modulation In this type of modulation, the continuous waveforms are sampled at regular intervals. Information is transmitted only at the sampling times.
The process of separating of audio signal from modulated signal is called demodulation.
An antenna converts electrical energy into electromagnetic waves at transmitting end and pick up transmitted signal at receiving end and converts electromagnetic waves into electrical signal.
The term modem is contraction of the term modulator and demodulator. Modem is a device which can modulate as well as demodulate the signal. It connect one computer to another through ordinary telephone lines.
Fax (Facsimile Telegraphy)
The electronic reproduction of a document at a distant place is called FAX
The radio waves are the electromagnetic waves of frequency ranging from 500 kHz to about 1000 MHz. These \V8VeS are used In the field of radio communication. With reference to the frequency range and wavelength range, the radio waves have been divided into various categories shown in table.
Frequency Range and Wavelength Range of Radio Waves
Propagation of Radio Waves
The three modes are discussed below.
(i) Ground Wave or Surface Wave Propagation It is suitable for low and medium frequency up to 2 MHz. It is used for local broad casting.
(ii) Sky Wave Propagation It is suitable for radio waves of frequency between 2 MHz to 30 MHz. It is used for long distance radio communication.
Critical Frequency The highest frequency of radio wave that can be reflected back by the ionosphere is called critical frequency.
Critical frequency, vc = 9 (Nmax)1 / 2
Where, Nmax = number density of electrons/metre3.
Skip Distance The minimum distance from the transmitter at which a sky wave of a frequency but not more than critical frequency, is sent back to the earth.
Skip distance (Dskip) = 2h (Vmax / Vc)2 – 1
where h is height of reflecting layer of atmosphere,
Vmax is maximum frequency of electromagnetic waves and Vc is critical frequency.
Fading The variation in the strength of a signal at receiver due to interference of waves, is called fading.
(iii) Space Wave Propagation It is suitable for 30 MHz to 300 MHz. It is used in television communication and radar communication. It is also called line of sight communication.
- Range is limited due to curvature of earth. If h be the height of the transmitting antenna, then signal can be received upto a maximum distance
d = √2RH
- If height of transmitting and receiving antennas be hT and hR respectively. The effective range will
- Microwaves are electromagnetic wave of frequency 1 to 300 GHz, greater than those of TV signals. The wavelength of microwaves is of the order of a few mm.
- Microwave communication is used in radar to locate the flying objects In space.
- These waves can be transmitted as beam signals in a particular direction, much better than radiowave,
- There is no diffraction of microwave around corners of an obstacle which happens to lie along its passage.
It IS carried out between a transmitter and a receiver through a satellite. A geostationary satellite is utilized for this purpose, whose time period is 24 hours.
A communication satellite is a space craft, provided with microwave receiver and transmitter. It is placed in an orbit around the earth. The India remote sensing satellites are
IRS-IA, IRS-IB and IRS-IC
The line-of-sight microwave communication through satellite is possible if the communication satellite is always at a fixed location with respect to the earth, e.g., the satellite which is acting as a repeater must be at rest with respect to the earth. It is so far a satellite known as geo-stationary satellite.
The basic requirements for geostationary satellites are as follows:
- The time period of revolution of the satellite around the earth is equal to the time period of rotation of earth about its polar axis i.e., 24 h.
- The sense of revolution of the satellite around the earth is the same as that of the earth about its polar axis i.e., from west to east.
- The orbital plane of revolution of satellite is concentric and coplanar with the equatorial plane of earth.
- The height of geostationary satellite above the equator of earth is nearly 36000 km and its orbital velocity is nearly 3.1 km/s.
The orbit in which the gee-satellite above revolves around the earth is known as geo-synchronous orbit. As its angular speed is synchronised with the angular speed of the earth. therefore, the geo-stationary satellite is also known as geo-synchronous satellite.
Merits of Satellites Communication
- The satellite communication covers wide area for broadcasting a8 compared to other communication systems i.e. it has wide coverage range.
- The satellite communication is also used effectively in mobile communication.
- The satellite communication is found to be much economical as compared to other communication systems on earth. Infact. the cost involved in satellite communication is independent of the distance.
- The satellite communication is most cost effective in remote and hilly areas, such as Ladakh, Himachal Pradesh etc.
- The satellite communication permits transmission of data at rate.
- The satellite communication is very accurate and economical search. rescue and navigation purposes.
Demerits of Satellite Communication
1. If a system on the satellite goes out of order due to environmental stresses, it is almost impossible to repair it.
2. In satellite communication, there is a time delay between transmission and reception, due to extremely large communication path length (greater than 2 x 36000 km). This delay causes a time gap during talking, which proves quite annoying.
It is a technique of observing or measuring the characteristics of the object at a distance. A polar satellite is utilized for this purpose.
Distance upto which a signal can be obtained from an antenna is given by
d = √2hR
where, h is height of antenna and R is radius of earth.
LED and Diode Laser in Communication
Light Emitting. Diode (LED) and diode laser are preferred sources for optical communication links to the following features.
- Each produces light of suitable power required in optical communication. Diode laser provides light which is monochromatic and coherent. This light is obtained as a parallel beam. It is used in very long distance transmission.
- LED provides almost monochromatics light. This suitable for small distance transmission. It is infact, a low cost device as compared to diode lasers.
- Transmission lines are used to interconnect points separated from each other. For example interconnection between a transmitter and a receiver or a transmitter and antenna or an antenna and a receiver are achieved through transmission lines.
- Line communication may be in the form of electrical signal or optical signal.
An optical fibre is a long thread consisting of a central core of glass or plastic of uniform refractive index. It is surrounded by a cladding of material of refractive index less than that of the core and a protective Jacket of insulating material.
There are three types of optical fibre configuration
- Single mode step index fibre
- Multi mode step index fibre
- Multi mode graded index fibre.
Applications of Optical Fibres
- A bundle of optical fibres is called light pipe. This pipe can transmit as image. Since the pipe is flexible, it can be twisted in any desired manner. Hence it is used medical and optical examination of even the inaccessible parts of human body, e.g., in endoscopy.
- Optical fibres are used in transmission and reception of electrical signals by coverting them first into light signals.
- Optical fibres are used in telephone and other transmitting cables. Each fibre can carry upto 2000 telephone messages without much loss of intensity.
Class 12 Key Points, Important Questions & Practice Papers
Hope these notes helped you in your schools exam preparation. Candidates can also check out the Key Points, Important Questions & Practice Papers for various Subjects for Class 12 in both Hindi and English language form the link below.
|Class 12 Physics||कक्षा 12 व्यावसायिक अध्ययन|
|Class 12 Chemistry||कक्षा 12 समाज शास्त्र|
|Class 12 Maths||कक्षा 12 अर्थशास्त्र|
|Class 12 Biology||कक्षा 12 भूगोल|
|Class 12 Business Studies|
|Class 12 Economics|
|Class 12 Sociology|
Class 12 NCERT Solutions
Candidates who are studying in Class 12 can also check Class 12 NCERT Solutions from here. This will help the candidates to know the solutions for all subjects covered in Class 12th. Candidates can click on the subject wise link to get the same. Class 12 Chapter-wise, detailed solutions to the questions of the NCERT textbooks are provided with the objective of helping students compare their answers with the sample answers.
Class 12 Mock Test / Practice
Mock test are the practice test or you can say the blue print of the main exam. Before appearing in the main examination, candidates must try mock test as it helps the students learn from their mistakes. With the help of Class 12 Mock Test / Practice, candidates can also get an idea about the pattern and marking scheme of that examination. For the sake of the candidates we are providing Class 12 Mock Test / Practice links below.
Class 12 Exemplar Questions
Exemplar Questions Class 12 is a very important resource for students preparing for the Examination. Here we have provided Exemplar Problems Solutions along with NCERT Exemplar Problems Class 12. Question from very important topics is covered by Exemplar Questions for Class 12.
Leave a Reply